Maloof Inspired Rocker, Charles Brock Plans 3

Last weekend I went over to my friends shop to use his Harbor Freight lathe, well, it had died. Apparently the motor had given up on its short, dubious quality life. Unfortunately for me I didn't know anyone else locally that has a lathe and I needed to turn the front legs for my rocker, so I did what any woodworker would do, I bought myself one, I mean, I really did need it to complete this project, really. So I went over to The WoodWhisperer's Amazon store because it really is a painless way to support a great site and to keep Marc able to keep supplying us with fantastic videos.

Once the turning was complete, and I was covered it Walnut chips, the front legs looked great in place and the chair is starting to look like a chair. Now onto the back legs, probably the most difficult part of the build so far. After creating the tapering jig that Mr. Brock describes in the book, I tapered the adder blocks on the rear legs to give the proper splay.

Then I cut the tenons on the table saw and rounded the inside corner on the router table. After a little fitting and fine tuning with my small router plane and some paring with a chisel the back legs fit nice and tight with just the right amount of splay.

With both rear legs in place and the front legs on it's really looking like a chair, tomorrow I'll drill some holes to attach the legs. Mr. Brock calls for a Miller stepped bit for the attachments of the front and rear legs, and also the headrest. I have some more cutting to do on the rear legs on the bandsaw and a little more shaping to do on the seat.

You'll notice the Rockler Bench cookies on my table, I've found these perfect for holding the coopered seat for shaping, in the DVD Mr. Brock uses what looks like a cradle custom made to hold the seat, but since I'm just making the one chair making a special jig to hold the seat seemed like overkill to me. I simply place the cookies on the table and set the seat on them, the cookies hold the seat securely when shaping and sanding. Next week, the arms, wish me luck.

"When a man is wrapped up in himself, he makes a pretty small package."
- John Ruskin

Maloof Inspired Rocker, Charles Brock Plans, 2

This weekend I worked on the seat, the front legs, and the back legs. I also rewatched the DVD yet again, it really is an invaluable tool. The first thing I did was to dust off my biscuit joiner and look all around the shop, I know I had some biscuits around here somewhere. In the DVD Mr. Brock uses Dominoes but he does suggest that you could use biscuits or dowels, they really are just to align the coopered seat. After checking seat for size I used a plane to trim off a few hundreds of an inch off of each of the ends. Once I was happy with everything I measured and marked for the joinery and cut it on the tablesaw. Using the 1/2 inch slotting bit that Mr. Brock recommends I trimmed the tenons for the legs. I trimmed excess material from the seat using the bandsaw then, using plenty of glue, clamped it up.
While the seat was cooking I picked some nicely figured Walnut for the front legs and cut them to size. Mr. Brock's instructions for laying out the mortises for the front legs were very easy to follow. I cut them to size then adjusted the fit with a router plane. Once this was complete I used the provided template to mark the front legs and cut the waste away on the bandsaw.

Once I took the seat out of the clamps the fun started, using an angle grinder and a Galahad carving wheel, I carved out the seat to a shape I liked then refined it with with a sanding wheel, a micro plane, and finally worked my way to 60 grit sandpaper on my Festool sander. I have to say that I never thought much about sanders until I got to use this unit with it's attached vacuum, does a better, cleaner job that any sander I've ever used, I have some DeWalt random orbit sanders that I used to attach to my shopvac, but it doesn't compare. I wanted to see how the seat was going to look so I splashed some mineral spirits on it and WOW!, it is beautiful.

The next thing I did was to select a board for the back legs and rough cut, then trimmed them out on the bandsaw, following this I attached the pattern and cleaned them up on the router table. The instructions call for an adder block to be glued to the inside of each leg, this was the last thing I did this weekend, stay tuned for more updates. Oh a last note, Charles Brock picked up my last post and linked it from his website! Unfortunately somehow my "about me" section had gotten turned off so he had no idea what my name was, and at the end of my post I added a quote from Douglas Adams, but I didn't put quotation marks around it, so, Mr. Brock called me Doug..., well, who really cares, I'm just psyched that he picked up my post.

"Always be wary of any helpful item that weighs less than its operating manual."
Terry Pratchett

Maloof inspired Rocker, Charles Brock plans

This post begins my journey into the world of sculpted rocking chairs. I've been wanting to attempt one of these for a few years but the passing of Sam Maloof last year and the release of Charles Brock's book/plan/dvd have pushed me to give it a go. I won't give a step by step instruction on what it takes to create one of these beauties such as the example of one of Mr. Brock's chair to the left, this is best left to his book/plan/DVD, instead I'll just keep you up with what I'm doing and how it's going as well as commenting on the Book itself.

I received "Build a Maloof Inspired Rocker" book/dvd/plan bundle for Christmas this year and was struck by the quality of the product, the book is well written and clear, the DVD is professionally produced and Mr. Brock does a great job showing each step in creating the rocker as well as giving helpful hint and tips throughout. The plans are full size 2x4 foot sheets that give you every template that you need to build the rocker. Mr. Brock is quick to tell you that he did not attempt to reproduce an exact replica of the Maloof rocker but was inspired by Mr. Maloof's body of work and wanted to create one himself. His methods are much easier to follow that the Hal Taylor downloadable book which I also have. After my first watching of the DVD I was confident that I could create a passable chair. I suggest that you watch the DVD all the way through and look through the book, then when you are planning your build, use the DVD and book together chapter by chapter.

The first thing that I did was to make a copy of the template plans at Staples just in case I messed up on cutting the templates, I did this also so that I could keep an archival copy of the plans for future builds.

After collecting the appropriate thicknesses of plywood and MDF plus some posterboard I cut out the templates and using artists spray adhesive adhered the paper to the wood and cut it out of the bandsaw then cleaned each up using the oscillating spindle sander and various files and sanding blocks. I also made the bending form for the rockers. The book has detailed instructions on creating each template and form and what thickness plywood to use for which template.

Following Mr. Brock's recommendation for BF I had ordered a stock of 8/4 Black Walnut and it have been acclimating in my shop for 3 months, today I cut, jointed and coopered the seat per his instruction.

I also ordered the router bits that he suggests in the book and DVD for shaping the joints for the leg/seat connection as none of the ones in my collection match in radius, this is the key to getting tight fitting joints on both the front and back legs.

This weekend I plan to rewatch the seat chapter again while following along in the book and then going to the shop to begin the joinery on the seat and start the shaping. More updates to come.

I may not have gone where I intended to go, but I think I have ended up where I needed to be.
- Douglas Adams

Limbert #366 Bookcase Finished

The last couple of weekends I spent most of my time finishing the Limbert bookcase, if you're not familiar with my finishing process check out my post on it here. It takes a few days to complete with drying time in between, so while I was waiting I was working on my Shaker table for The Woodwhisperer Guild March Woodworkers Fighting Cancer build. It was kind of nice having two projects going on at the same time, if I got bored with sanding I could switch over to tapering the legs of the table, if I didn't have much time I could work on the drawer. I decided to go with a medium brown finish for the bookcase so I started with medium brown dye and I used brown Mahogany gel stain for the over stain. I took the time to finish the backing plywood prior to attaching it to the back of the case with 1/2 inch staples to allow for any wood movement.
Once the dark wax was mostly dry I had a friend help me carry it into the house, all that quartersawn white oak is heavy. After letting the wax cure overnight I couldn't wait to set up my vintage Kodak camera collection on the top and fill the bookcase with my woodworking and photography books that have been piled on my dining room table for months. Then I decompressed some of my other bookcases leaving me with a whole empty shelf to expand in to.
I was very happy with the way this project came together, I started with just some pictures and measurements, used Sketchup to make them into a workable plan and went on from there. One detail that I didn't cover in my
previous posts is the bevel on the edge of the adjustable shelves, its a nice little touch that you can see in the pictures or some of the antiques. I created the bevel the same way I did on the top of the Shaker table, I adjusted the angle of my tablesaw to 12.5 degrees and set the fence 1/2 inch away from the blade. Using a tall fence and a magnetic featherboard I carefully moved the shelves vertically past the blade. Cuts like this almost always leave burn marks so a little clean up with a low angle smoothing plane was in order. Every time I make something I learn something new, sometimes something big, sometimes something small, I noticed with this bookcase sitting near my last one that my sanding and finishing have improved. I learned on this one that it is easier to finish a bookcase with the back not attached, a lot easier.

"Happiness is not something ready made. It comes from your own actions."

- His Holiness the Dalai Lama

Limbert #366 Bookcase, Part 2

Last weekend I cut and routed the dadoes and grooves in the sides of the Limbert #366 bookcase. During the week I took a few hours and, using the template I marked out the cutouts and the bottom lift. After drilling a few access holes and cutting the waste out with a jigsaw I used the template and a 3/4 inch pattern cutting bit to clean up the cuts. I also cut the adjustable shelves to size and added the bevel on the front of each shelf.

Saturday I cut and glued up the top for my cherry Shaker table for the Woodwhisperer Guild Woodworkers Fighting Cancer build, then I moved on to sanding the bookcase. I ran the complete sanding schedule I use for white oak, starting with 60 grit, then 80, 120 and finally 180 grit. Between 120 and 180 grit on the inside of the sides I drilled the shelf pin holes for the adjustable shelves. I don't use a fancy template for this, I have a section of pegboard with two lines of holes 8 inches apart marked every 2 inches. With this I use a 1/4 inch brad point drill bit with a stop collar in place to drill 1/2 inch deep holes. I've used this on many projects and have never had problems with it, its simple, its cheap and I can make custom templates for any project.

The final dryfit was done after hand fitting each part, a few clamps were used to hold everything together and tight while I took measurements to insure that everything was square. I took the rest of the afternoon to make a taper cutting jig for the tablesaw inspired by Marc's live Guild event as I would need to cut long tapers for the Shaker table.
Today I had to run to Lowes to get some oak ply for the back of the bookcase, all of the pictures of the original that I could find show a plywood back so why not? I gathered my long clamps and glue bottle and completed the glueup. After a couple of hours of drying I flipped the bookcase onto its face and measured for the plywood back. After cutting and sanding the plywood I placed it and attached it with some blue tape for the pictures leaving it unattached to make finishing easier.

I took the rest of the day to cut the mortises in the Shaker table and taper the legs. Also I took the top for the table out of the clamps and rough sanded it.

One of the features that attracted me to this particular bookcase is the detail on top of the piece. The small fixed shelf and the cutouts along with the solid wood back and the large fixed top shelf are very nice and would make a perfect place for me to keep part of my vintage Kodak camera collection. I can't wait to complete the finish and get this bookcase in the house.

"Take everything you like seriously, except yourselves."

Rudyard Kipling

Limbert #366 Bookcase

When I started my journey into Arts and Crafts furniture I was of course drawn to Stickley's designs, his being the most common in the literature. As I got further along I discovered Charles Limbert and his unique take on furniture. Limbert was a student of European designers, particularly Charles Rennie Mackintosh of the Glasgow school, his designs are noted by cutouts and curves. I've made many Limbert pieces and blogged about them here. I found this bookcase in a reprint of an early 1900's Limbert catalog and searched online auction catalogs until I found this one.

Limbert produced this model with and without a door, and in a double wide version. The single door version fits the size that I want, its 64 inches tall, 12 inches deep and 30 inches wide. I'm not sure if I will add the door or not, but for now I'm proceeding with the assumption that I won't have a door. I took the photo into Google Sketchup and with the know dimensions produced a plan that I've uploaded in The Wood Whisperer Community.

From this model I produced a cutlist and exploded details of the parts. Saturday was spent preparing the Quartersawn White Oak stock and gluing up the parts, I also created a template for the rectangular cutouts at the top of the bookcase and the small lift at the bottom. Sunday I took everything out of the clamps and cleaned off the boards. I trimmed each piece down to the correct size and cut the 3/8th inch dado along the back of the sides and on the top and bottom shelves. Using a T-square guide and a plunge router I cut the dadoes for the top and bottom shelves and for the small shelf. I switched to the router guide and a 3/8th inch bit and cut the mortises for the top and bottom aprons. After squaring up the end of the small shelf dado with a chisel I cut the tenons on the aprons using the dado blade still in the tablesaw.

After doing a little fitting of the pieces with a routerplane and chisel I was able to complete an initial dryfit before calling it a day. I wanted to get a good start on this build because starting next weekend I'll be beginning the Guild March Shaker table project as part of Woodworker's fighting cancer. I'll be recording my progress of the Shaker table and continuing on with this project so look for updates.

"First things first, but not neccessarily in that order." - Dr. Who

The Beginning

I know that I can make a nice wall cabinet, the challenge with this project was the inlay that I had thought of for the door. That being said, I decided to start with what for me is usually the end, the door. This is going to be a stand alone wall cabinet to replace a smaller one in my bedroom, it's made from Cherry and I wanted to incorporate a bolection inlay of a Japanese Cherry tree on the door. I've never done a bolection inlay before and wasn't sure if I could pull it off well enough so I wanted to complete the inlay first to leave me multiple options with the design if I couldn't pull it off.

I started by selecting an interesting grain pattern and cutting it to size of the planned door. I wanted the underlying grain to mimic the mountains that you would see in the background of a Japanese print.

With the grain pattern set I sketched out a Cherry tree on large graph paper, at this point I had in my mind how I was going to do the wood of the tree but I still wasn't sure about the blossoms. I cut the sketch of the trunk into smaller components and using spray adhesive I attached them to pieces of 3/16 inch thick walnut aligning the grain in pleasing ways. After cutting out all the pieces on the scroll saw I used double sided tape to hole the walnut to the door and outlined them with a sharp Exacto knife. Working with one component at time I then routed a 1/16th inch deep relief into the door. After fitting the piece I then would move on to the next piece, completing the tree in a few days between finishing up Christmas projects. I still had in my mind that I would cut the blossoms and without routing glue them to the door and shape them with my Foredom power carver. I tried this method as a test and was very disappointed. The small blossoms were very hard to cut on the scroll saw and attempting to shape them scarred up the base wood. I gave up on this approach.

As often happens I had an epiphany in the shower, I'd go abstract and simple. After I dried off and dressed I went out into the shop and using a 3/8th inch plug cutter I cut a scrap of curly maple into plugs. I drilled some 3/8th inch holes into some scrap cherry and drove the plugs in. I trimmed the plugs with a chisel and shaped them with a sanding block. I noticed that there was a slight space around the plugs and that all of one size would look odd, so I undersized the drill bit by 1/64th of an inch and tried that. The plugs fit very tight and after trimming and shaping there was no space around the plug. I then moved to the drill press and cut 3/8th and 1/4 inch plugs from a block of curly maple. I started placing holes where they looked good and plugging them, I kept adding them here and there until I was happy. After trimming them and sanding the plugs and the trunk I decided that the project was a success and the wall cabinet could proceed with this design. More to come as the cabinet takes shape.

"The beginning is the most important part of the work." - Plato

Limbert #234 Tabourette, Part 2

Well here it is, the Limbert #234 Tabourette completed. The build was very easy with no complicated joinery. Download the Sketchup plan here, make some simple patterns and go for it.
The finish is a little different from my previous posts, on this table I decided to skip the shellac for the final layers and go with Arm-r-seal from General Finishes. The result is really nice and has a more satin finish than the shellac, I still topped it all off with Watco dark liquid wax as usual.

The top is attached to the base with figure 8 table irons to allow for any movement and I aplied felt pads to the feet as it going to live on a hardwood floor.

My neighbor was very happy with the final result and is looking forward to the coffee table that I designed to go along with it, more on that in a series of later posts.

"No matter where you go, there you are" Buckaroo Bonzia

Limbert #234 Tabourette, Part 1

My neighbor asked me to make her an end table and a coffee table in the arts and crafts style to go in her bungalow. I showed her some of the completed pieces in my house and she was drawn more to the Limbert style. I did some more research in my books and online and came up with this little tabourette as an end table, I showed her the pictures and described my idea for a coffee table that would compliment the design of the end table. Coffee tables weren't a part of American homes in the 1900's but I took a Limbert cocktail table and lowered it and changed it some to make it a coffee table, more on that in a later post.

In previous posts I have described my method of scaling plans from pictures but luckily I was able to find descriptions of this table along with dimensions, which are 16"x16"x18" tall. These relate to the widest measurements, the top which will be square. From this and the photos I came up with the dimensions in the picture at the left.

Using Google Sketchup I created a model of the table along with dimensioned elevations, I was also able to look at the components and come up with construction details such as how to connect the sides.

After removing the stock from the clamps and trimming it to size I took this template I made up from the plan above and marked out the areas to be cut out. After removing the bulk of the waste with a jigsaw for the cut outs and the bandsaw for the bottom I carefully aligned the template to the inside of each side piece and screwed it in place. Using a template like this for routing is always good, you can attach it with double sided tape or if piece has a hidden side you can just screw the template to the stock. I used a 1/2 inch pattern cutting bit in the router table to give the cutouts the proper radius at the corners. After this I cut a 45 degree miter on each side of the side pieces.

What followed was some sanding and a little hand work on the cutouts then I glued the miters together using the miter cutoffs as glue blocks a little time cooking in the clamps while I sanded the top. A final sanding on everything inside and out and attaching the top with figure 8 table irons, a little more touch up sanding and a cleaning finished up this project for the weekend and now all that is left if finishing. My neighbor looked at the finish samples that I keep and picked the middle range of the five I have so when I start on the finish I just turn over the sample and the "recipe" is written on the back. For more on my arts and crafts finish and a look at the samples see this post.

" Be who you are and say what you feel because those who mind don't matter, and those that matter don't mind." Dr. Seuss

Music Stand part 3

This weekend I started out by sanding all the flat surfaces of the mahogany ribs and then taking to the edges and curves off everything with a folded piece of sandpaper . There are no pictures of this because I don't like getting dust all over my camera. Once I started to assemble the music stand I didn't think that I would need to clamp the ribs into the stand because the fit was tight enough that the last they took a gentle rap with a deadblow hammer to drive each one that final smidge, but I decided to err on the safe side and clamped each rib in place just in case the glue would piston one of the ribs out as it set up.

After a little more hand sanding and the first two coats of Watco Natural Danish Oil I decided to take the stand out onto the lawn for a better shot. I think it turned out great so far, with many more coats of Danish Oil and a coat of wax this stand will glow.

“Be who you are and say what you feel because those who mind don’t matter and those who matter don’t mind.” ~Dr. Seuss